Insulated-gate bipolar transistor
IGBT module (IGBTs and freewheeling diodes) with a rated current of 1200 A and a maximum voltage of 3300 V
Working principleSemiconductor
Invented1959
Electronic symbol

IGBT schematic symbol

An insulated-gate bipolar transistor (IGBT) is a three-terminal power semiconductor device primarily forming an electronic switch. It was developed to combine high efficiency with fast switching. It consists of four alternating layers (P–N–P–N) that are controlled by a metal–oxide–semiconductor (MOS) gate structure.

Although the structure of the IGBT is topologically similar to a thyristor with a "MOS" gate (MOS-gate thyristor), the thyristor action is completely suppressed, and only the transistor action is permitted in the entire device operation range. It is used in switching power supplies in high-power applications: variable-frequency drives (VFDs), uninterruptible power supply systems (UPS), electric cars, trains, variable-speed refrigerators, lamp ballasts, arc-welding machines, induction hobs, and air conditioners.

Since it is designed to turn on and off rapidly, the IGBT can synthesize complex waveforms with pulse-width modulation and low-pass filters, thus it is also used in switching amplifiers in sound systems and industrial control systems. In switching applications modern devices feature pulse repetition rates well into the ultrasonic-range frequencies, which are at least ten times higher than audio frequencies handled by the device when used as an analog audio amplifier. As of 2010, the IGBT was the second most widely used power transistor, after the power MOSFET.

IGBT comparison table[1]
Device characteristic Power BJT Power MOSFET IGBT
Voltage rating High <1 kV High <1 kV Very high >1 kV
Current rating High <500 A Low <200 A High >500 A
Input drive Current ratio
hFE ~ 20–200
Voltage
VGS ~ 3–10 V
Voltage
VGE ~ 4–8 V
Input impedance Low High High
Output impedance Low Medium Low
Switching speed Slow (µs) Fast (ns) Medium
Cost Low Medium High

Device structure

Cross-section of a typical IGBT showing internal connection of MOSFET and bipolar device

An IGBT cell is constructed similarly to an n-channel vertical-construction power MOSFET, except the n+ drain is replaced with a p+ collector layer, thus forming a vertical PNP bipolar junction transistor. This additional p+ region creates a cascade connection of a PNP bipolar junction transistor with the surface n-channel MOSFET.

History

Static characteristic of an IGBT

The metal–oxide–semiconductor field-effect transistor (MOSFET) was invented by Mohamed M. Atalla and Dawon Kahng at Bell Labs in 1959.[2] The basic IGBT mode of operation, where a pnp transistor is driven by a MOSFET, was first proposed by K. Yamagami and Y. Akagiri of Mitsubishi Electric in the Japanese patent S47-21739, which was filed in 1968.[3]

Following the commercialization of power MOSFETs in the 1970s, B. Jayant Baliga submitted a patent disclosure at General Electric (GE) in 1977 describing a power semiconductor device with the IGBT mode of operation, including the MOS gating of thyristors, a four-layer VMOS (V-groove MOSFET) structure, and the use of MOS-gated structures to control a four-layer semiconductor device. He began fabricating the IGBT device with the assistance of Margaret Lazeri at GE in 1978 and successfully completed the project in 1979.[4] The results of the experiments were reported in 1979.[5][6] The device structure was referred to as a "V-groove MOSFET device with the drain region replaced by a p-type anode region" in this paper and subsequently as "the insulated-gate rectifier" (IGR),[7] the insulated-gate transistor (IGT),[8] the conductivity-modulated field-effect transistor (COMFET)[9] and "bipolar-mode MOSFET".[10]

An MOS-controlled triac device was reported by B. W. Scharf and J. D. Plummer with their lateral four-layer device (SCR) in 1978.[11] Plummer filed a patent application for this mode of operation in the four-layer device (SCR) in 1978. USP No. 4199774 was issued in 1980, and B1 Re33209 was reissued in 1996.[12] The IGBT mode of operation in the four-layer device (SCR) switched to thyristor operation if the collector current exceeded the latch-up current, which is known as "holding current" in the well known theory of the thyristor.

The development of IGBT was characterized by the efforts to completely suppress the thyristor operation or the latch-up in the four-layer device because the latch-up caused the fatal device failure. IGBTs had, thus, been established when the complete suppression of the latch-up of the parasitic thyristor was achieved as described in the following.

Hans W. Becke and Carl F. Wheatley developed a similar device, for which they filed a patent application in 1980, and which they referred to as "power MOSFET with an anode region".[13][14] The patent claimed that "no thyristor action occurs under any device operating conditions". The device had an overall similar structure to Baliga's earlier IGBT device reported in 1979, as well as a similar title.[4]

A. Nakagawa et al. invented the device design concept of non-latch-up IGBTs in 1984.[15] The invention[16] is characterized by the device design setting the device saturation current below the latch-up current, which triggers the parasitic thyristor. This invention realized complete suppression of the parasitic thyristor action, for the first time, because the maximal collector current was limited by the saturation current and never exceeded the latch-up current.

In the early development stage of IGBT, all the researchers tried to increase the latch-up current itself in order to suppress the latch-up of the parasitic thyristor. However, all these efforts failed because IGBT could conduct enormously large current. Successful suppression of the latch-up was made possible by limiting the maximal collector current, which IGBT could conduct, below the latch-up current by controlling/reducing the saturation current of the inherent MOSFET. This was the concept of non-latch-up IGBT. “Becke’s device” was made possible by the non-latch-up IGBT.

The IGBT is characterized by its ability to simultaneously handle a high voltage and a large current. The product of the voltage and the current density that the IGBT can handle reached more than 5×105 W/cm2,[17][18] which far exceeded the value, 2×105 W/cm2, of existing power devices such as bipolar transistors and power MOSFETs. This is a consequence of the large safe operating area of the IGBT. The IGBT is the most rugged and the strongest power device yet developed, affording ease of use and so displacing bipolar transistors and even GTOs. This excellent feature of the IGBT had suddenly emerged when the non-latch-up IGBT was established in 1984 by solving the problem of so-called “latch-up,” which is the main cause of device destruction or device failure. Before that, the developed devices were very weak and were easy to be destroyed because of “latch-up.”

Practical devices

Practical devices capable of operating over an extended current range were first reported by B. Jayant Baliga et al. in 1982.[7] The first experimental demonstration of a practical discrete vertical IGBT device was reported by Baliga at the IEEE International Electron Devices Meeting (IEDM) that year.[19][7] General Electric commercialized Baliga's IGBT device the same year.[4] Baliga was inducted into the National Inventors Hall of Fame for the invention of the IGBT.[20]

A similar paper was also submitted by J. P. Russel et al. to IEEE Electron Device Letter in 1982.[9] The applications for the device were initially regarded by the power electronics community to be severely restricted by its slow switching speed and latch-up of the parasitic thyristor structure inherent within the device. However, it was demonstrated by Baliga and also by A. M. Goodman et al. in 1983 that the switching speed could be adjusted over a broad range by using electron irradiation.[8][21] This was followed by demonstration of operation of the device at elevated temperatures by Baliga in 1985.[22] Successful efforts to suppress the latch-up of the parasitic thyristor and the scaling of the voltage rating of the devices at GE allowed the introduction of commercial devices in 1983,[23] which could be utilized for a wide variety of applications. The electrical characteristics of GE's device, IGT D94FQ/FR4, were reported in detail by Marvin W. Smith in the proceedings of PCI April 1984.[24] Marvin W. Smith showed in Fig.12 of the proceedings that turn-off above 10 amperes for gate resistance of 5kOhm and above 5 amperes for gate resistance of 1kOhm was limited by switching safe operating area although IGT D94FQ/FR4 was able to conduct 40 amperes of collector current. Marvin W. Smith also stated that the switching safe operating area was limited by the latch-up of the parasitic thyristor.

Complete suppression of the parasitic thyristor action and the resultant non-latch-up IGBT operation for the entire device operation range was achieved by A. Nakagawa et al. in 1984.[15] The non-latch-up design concept was filed for US patents.[25] To test the lack of latch-up, the prototype 1200 V IGBTs were directly connected without any loads across a 600 V constant voltage source and were switched on for 25 microseconds. The entire 600 V was dropped across the device and a large short circuit current flowed. The devices successfully withstood this severe condition. This was the first demonstration of so-called "short-circuit-withstanding-capability" in IGBTs. Non-latch-up IGBT operation was ensured, for the first time, for the entire device operation range.[18] In this sense, the non-latch-up IGBT proposed by Hans W. Becke and Carl F. Wheatley was realized by A. Nakagawa et al. in 1984. Products of non-latch-up IGBTs were first commercialized by Toshiba in 1985. This was the real birth of the present IGBT.

Once the non-latch-up capability was achieved in IGBTs, it was found that IGBTs exhibited very rugged and a very large safe operating area. It was demonstrated that the product of the operating current density and the collector voltage exceeded the theoretical limit of bipolar transistors, 2×105 W/cm2, and reached 5×105 W/cm2.[17][18]

The insulating material is typically made of solid polymers which have issues with degradation. There are developments that use an ion gel to improve manufacturing and reduce the voltage required.[26]

The first-generation IGBTs of the 1980s and early 1990s were prone to failure through effects such as latchup (in which the device will not turn off as long as current is flowing) and secondary breakdown (in which a localized hotspot in the device goes into thermal runaway and burns the device out at high currents). Second-generation devices were much improved. The current third-generation IGBTs are even better, with speed rivaling power MOSFETs, and excellent ruggedness and tolerance of overloads.[17] Extremely high pulse ratings of second and third-generation devices also make them useful for generating large power pulses in areas including particle and plasma physics, where they are starting to supersede older devices such as thyratrons and triggered spark gaps. High pulse ratings and low prices on the surplus market also make them attractive to the high-voltage hobbyists for controlling large amounts of power to drive devices such as solid-state Tesla coils and coilguns.

Patent issues

The device proposed by J. D. Plummer in 1978 (US Patent Re.33209) is the same structure as a thyristor with a MOS gate. Plummer discovered and proposed that the device can be used as a transistor although the device operates as a thyristor in higher current density level.[27] The device proposed by J. D. Plummer is referred here as “Plummer’s device.” On the other hand, Hans W. Becke proposed, in 1980, another device in which the thyristor action is eliminated under any device operating conditions although the basic device structure is the same as that proposed by J. D. Plummer. The device developed by Hans W. Becke is referred here as “Becke’s device” and is described in US Patent 4364073. The difference between “Plummer’s device” and “Becke’s device” is that “Plummer’s device” has the mode of thyristor action in its operation range and “Becke’s device” never has the mode of thyristor action in its entire operation range. This is a critical point, because the thyristor action is the same as so-called “latch-up.” “Latch-up” is the main cause of fatal device failure. Thus, theoretically, “Plummer’s device” never realizes a rugged or strong power device which has a large safe operating area. The large safe operating area can be achieved only after “latch-up” is completely suppressed and eliminated in the entire device operation range. However, the Becke's patent (US Patent 4364073) did not disclose any measures to realize actual devices.

Despite Becke's patent describing a similar structure to Baliga's earlier IGBT device,[4] several IGBT manufacturers paid the license fee of Becke's patent.[13] Toshiba commercialized “non-latch-up IGBT” in 1985. Stanford University insisted in 1991 that Toshiba's device infringed US Patent RE33209 of “Plummer’s device.” Toshiba answered that “non-latch-up IGBTs” never latched up in the entire device operation range and thus did not infringe US Patent RE33209 of “Plummer’s patent.” Stanford University never responded after Nov. 1992. Toshiba purchased the license of “Becke’s patent” but never paid any license fee for “Plummer’s device.” Other IGBT manufacturers also paid the license fee for Becke's patent.

Applications

As of 2010, the IGBT is the second most widely used power transistor, after the power MOSFET. The IGBT accounts for 27% of the power transistor market, second only to the power MOSFET (53%), and ahead of the RF amplifier (11%) and bipolar junction transistor (9%).[28] The IGBT is widely used in consumer electronics, industrial technology, the energy sector, aerospace electronic devices, and transportation.

Advantages

The IGBT combines the simple gate-drive characteristics of power MOSFETs with the high-current and low-saturation-voltage capability of bipolar transistors. The IGBT combines an isolated-gate FET for the control input and a bipolar power transistor as a switch in a single device. The IGBT is used in medium to high-power applications like switched-mode power supplies, traction motor control and induction heating. Large IGBT modules typically consist of many devices in parallel and can have very high current-handling capabilities in the order of hundreds of amperes with blocking voltages of 6500 V. These IGBTs can control loads of hundreds of kilowatts.

Comparison with power MOSFETs

An IGBT features a significantly lower forward voltage drop compared to a conventional MOSFET in higher blocking voltage rated devices, although MOSFETS exhibit much lower forward voltage at lower current densities due to the absence of a diode Vf in the IGBT's output BJT. As the blocking voltage rating of both MOSFET and IGBT devices increases, the depth of the n- drift region must increase and the doping must decrease, resulting in roughly square relationship decrease in forward conduction versus blocking voltage capability of the device. By injecting minority carriers (holes) from the collector p+ region into the n- drift region during forward conduction, the resistance of the n- drift region is considerably reduced. However, this resultant reduction in on-state forward voltage comes with several penalties:

  • The additional PN junction blocks reverse current flow. This means that unlike a MOSFET, IGBTs cannot conduct in the reverse direction. In bridge circuits, where reverse current flow is needed, an additional diode (called a freewheeling diode) is placed in parallel (actually anti-parallel) with the IGBT to conduct current in the opposite direction. The penalty isn't overly severe because at higher voltages, where IGBT usage dominates, discrete diodes have a significantly higher performance than the body diode of a MOSFET.
  • The reverse bias rating of the N-drift region to collector P+ diode is usually only of tens of volts, so if the circuit application applies a reverse voltage to the IGBT, an additional series diode must be used.
  • The minority carriers injected into the N-drift region take time to enter and exit or recombine at turn-on and turn-off. This results in longer switching times, and hence higher switching loss compared to a power MOSFET.
  • The on-state forward voltage drop in IGBTs behaves very differently from power MOSFETS. The MOSFET voltage drop can be modeled as a resistance, with the voltage drop proportional to current. By contrast, the IGBT has a diode-like voltage drop (typically of the order of 2V) increasing only with the log of the current. Additionally, MOSFET resistance is typically lower for smaller blocking voltages, so the choice between IGBTs and power MOSFETS will depend on both the blocking voltage and current involved in a particular application.

In general, high voltage, high current and low switching frequencies favor the IGBT while low voltage, medium current and high switching frequencies are the domain of the MOSFET.

IGBT

Circuits with IGBTs can be developed and modeled with various circuit simulating computer programs such as SPICE, Saber, and other programs. To simulate an IGBT circuit, the device (and other devices in the circuit) must have a model which predicts or simulates the device's response to various voltages and currents on their electrical terminals. For more precise simulations the effect of temperature on various parts of the IGBT may be included with the simulation. Two common methods of modeling are available: device physics-based model, equivalent circuits or macromodels. SPICE simulates IGBTs using a macromodel that combines an ensemble of components like FETs and BJTs in a Darlington configuration. An alternative physics-based model is the Hefner model, introduced by Allen Hefner of the National Institute of Standards and Technology. Hefner's model is fairly complex but has shown good results. Hefner's model is described in a 1988 paper and was later extended to a thermo-electrical model which include the IGBT's response to internal heating. This model has been added to a version of the Saber simulation software.[29]

IGBT failure mechanisms

The failure mechanisms of IGBTs includes overstress (O) and wearout(wo) separately.

The wearout failures mainly include bias temperature instability (BTI), hot carrier injection (HCI), time-dependent dielectric breakdown (TDDB), electromigration (ECM), solder fatigue, material reconstruction, corrosion. The overstress failures mainly include electrostatic discharge (ESD), latch-up, avalanche, secondary breakdown, wire-bond liftoff and burnout.[30]

IGBT modules

See also

References

  1. Basic Electronics Tutorials.
  2. "1960: Metal Oxide Semiconductor (MOS) Transistor Demonstrated". The Silicon Engine: A Timeline of Semiconductors in Computers. Computer History Museum. Retrieved August 31, 2019.
  3. Majumdar, Gourab; Takata, Ikunori (2018). Power Devices for Efficient Energy Conversion. CRC Press. pp. 144, 284, 318. ISBN 9781351262316.
  4. 1 2 3 4 Baliga, B. Jayant (2015). The IGBT Device: Physics, Design and Applications of the Insulated Gate Bipolar Transistor. William Andrew. pp. xxviii, 5–12. ISBN 9781455731534.
  5. Baliga, B. Jayant (1979). "Enhancement- and depletion-mode vertical-channel m.o.s. gated thyristors". Electronics Letters. 15 (20): 645–647. Bibcode:1979ElL....15..645J. doi:10.1049/el:19790459. ISSN 0013-5194.
  6. "Advances in Discrete Semiconductors March On". Power Electronics Technology. Informa: 52–6. September 2005. Archived (PDF) from the original on 22 March 2006. Retrieved 31 July 2019.
  7. 1 2 3 Baliga, B.J.; Adler, M.S.; Gray, P.V.; Love, R.P.; Zommer, N. (1982). "The insulated gate rectifier (IGR): A new power switching device". 1982 International Electron Devices Meeting. pp. 264–267. doi:10.1109/IEDM.1982.190269. S2CID 40672805.
  8. 1 2 Baliga, B.J. (1983). "Fast-switching insulated gate transistors". IEEE Electron Device Letters. 4 (12): 452–454. Bibcode:1983IEDL....4..452B. doi:10.1109/EDL.1983.25799. S2CID 40454892.
  9. 1 2 Russell, J.P.; Goodman, A.M.; Goodman, L.A.; Neilson, J.M. (1983). "The COMFET—A new high conductance MOS-gated device". IEEE Electron Device Letters. 4 (3): 63–65. Bibcode:1983IEDL....4...63R. doi:10.1109/EDL.1983.25649. S2CID 37850113.
  10. Nakagawa, Akio; Ohashi, Hiromichi; Tsukakoshi, Tsuneo (1984). "High Voltage Bipolar-Mode MOSFET with High Current Capability". Extended Abstracts of the 1984 International Conference on Solid State Devices and Materials. doi:10.7567/SSDM.1984.B-6-2.
  11. Scharf, B.; Plummer, J. (1978). A MOS-controlled triac device. 1978 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. Vol. XXI. pp. 222–223. doi:10.1109/ISSCC.1978.1155837. S2CID 11665546.
  12. B1 Re33209 is attached in the pdf file of Re 33209.
  13. 1 2 U. S. Patent No. 4,364,073, Power MOSFET with an Anode Region, issued December 14, 1982 to Hans W. Becke and Carl F. Wheatley.
  14. "C. Frank Wheatley, Jr., BSEE". Innovation Hall of Fame at A. James Clark School of Engineering.
  15. 1 2 Nakagawa, A.; Ohashi, H.; Kurata, M.; Yamaguchi, H.; Watanabe, K. (1984). "Non-latch-up 1200V 75A bipolar-mode MOSFET with large ASO". 1984 International Electron Devices Meeting. pp. 860–861. doi:10.1109/IEDM.1984.190866. S2CID 12136665.
  16. A. Nakagawa, H. Ohashi, Y. Yamaguchi, K. Watanabe and T. Thukakoshi, "Conductivity modulated MOSFET" US Patent No. 6025622 (Feb. 15, 2000), No. 5086323 (Feb. 4, 1992) and No. 4672407 (Jun. 9, 1987).
  17. 1 2 3 Nakagawa, A.; Yamaguchi, Y.; Watanabe, K.; Ohashi, H. (1987). "Safe operating area for 1200-V nonlatchup bipolar-mode MOSFET's". IEEE Transactions on Electron Devices. 34 (2): 351–355. Bibcode:1987ITED...34..351N. doi:10.1109/T-ED.1987.22929. S2CID 25472355.
  18. 1 2 3 Nakagawa, A.; Yamaguchi, Y.; Watanabe, K.; Ohashi, H.; Kurata, M. (1985). "Experimental and numerical study of non-latch-up bipolar-mode MOSFET characteristics". 1985 International Electron Devices Meeting. pp. 150–153. doi:10.1109/IEDM.1985.190916. S2CID 24346402.
  19. Shenai, K. (2015). "The Invention and Demonstration of the IGBT [A Look Back]". IEEE Power Electronics Magazine. 2 (2): 12–16. doi:10.1109/MPEL.2015.2421751. ISSN 2329-9207. S2CID 37855728.
  20. "NIHF Inductee Bantval Jayant Baliga Invented IGBT Technology". National Inventors Hall of Fame. Retrieved 17 August 2019.
  21. Goodman, A.M.; Russell, J.P.; Goodman, L.A.; Nuese, C.J.; Neilson, J.M. (1983). "Improved COMFETs with fast switching speed and high-current capability". 1983 International Electron Devices Meeting. pp. 79–82. doi:10.1109/IEDM.1983.190445. S2CID 2210870.
  22. Baliga, B.Jayant (1985). "Temperature behavior of insulated gate transistor characteristics". Solid-State Electronics. 28 (3): 289–297. Bibcode:1985SSEle..28..289B. doi:10.1016/0038-1101(85)90009-7.
  23. Product of the Year Award: "Insulated Gate Transistor", General Electric Company, Electronics Products, 1983.
  24. Marvin W. Smith, "APPLICATIONS OF INSULATED GATE TRANSISTORS" PCI April 1984 PROCEEDINGS, pp. 121-131, 1984 (Archived PDF )
  25. A.Nakagawa, H. Ohashi, Y. Yamaguchi, K. Watanabe and T. Thukakoshi, "Conductivity modulated MOSFET" US Patent No.6025622(Feb.15, 2000), No.5086323 (Feb.4, 1992) and No.4672407(Jun.9, 1987)
  26. "Ion Gel as a Gate Insulator in Field Effect Transistors". Archived from the original on 2011-11-14.
  27. Scharf, B.; Plummer, J. (1978). "A MOS-controlled triac device". 1978 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. pp. 222–223. doi:10.1109/ISSCC.1978.1155837. S2CID 11665546.
  28. "Power Transistor Market Will Cross $13.0 Billion in 2011". IC Insights. June 21, 2011. Retrieved 15 October 2019.
  29. Hefner, A.R.; Diebolt, D.M. (September 1994). "An experimentally verified IGBT model implemented in the Saber circuit simulator". IEEE Transactions on Power Electronics. 9 (5): 532–542. Bibcode:1994ITPE....9..532H. doi:10.1109/63.321038. S2CID 53487037.
  30. Patil, N.; Celaya, J.; Das, D.; Goebel, K.; Pecht, M. (June 2009). "Precursor Parameter Identification for Insulated Gate Bipolar Transistor (IGBT) Prognostics". IEEE Transactions on Reliability. 58 (2): 271–276. doi:10.1109/TR.2009.2020134. S2CID 206772637.

Further reading

This article is issued from Wikipedia. The text is licensed under Creative Commons - Attribution - Sharealike. Additional terms may apply for the media files.